![APLICACIONES AUTOMOTRICES](https://cdn.ready-market.com.tw/cdb12976/Templates/pic/m/Promotion-Application-01.jpg?v=34c833ab)
APLICACIONES AUTOMOTRICES
Resistor de precisión de película delgada 0.01%, TC2ppm, wirebondale, anti-corrosión, MELF. Sensado...
Lee masInductor de chip de ferrita bobinada, alta potencia, tamaños pequeños, circuito magnético cerrado evita la diafonía, adecuado para instalación de alta densidad y soldadura de reflujo. Utilizado en todo tipo de dispositivos electrónicos, computadoras, convertidores.
MLP Series1008 ±20% 0.47μH 0.022 Ω 6.2A 4.9A
Tamaño | Tolerancia | Inductancia | Condición de prueba | DCR (Ω) máximo. | I sat (A) máximo | I rms (A) máximo |
---|---|---|---|---|---|---|
1008 | ±20% | 0.47 | 1MHz, 1mA | 0.022 | 6.2 | 4.9 |
MLPH06 (0806) Wire Wound Type Power Inductor
Codes | Inductance (uH) | Tolerance | Test Condition | DCR (mΩ) max. | Isat (A) max. | Irms (A) max. |
---|---|---|---|---|---|---|
R47 | 0.47 | ± 20% | 1MHz, 1V | 30 | 5.30 | 4.05 |
1R0 | 1.0 | ± 20% | 1MHz, 1V | 60 | 3.30 | 3.00 |
1R5 | 1.5 | ± 20% | 1MHz, 1V | 99 | 3.10 | 2.20 |
2R2 | 2.2 | ± 20% | 1MHz, 1V | 140 | 2.45 | 2.00 |
MLPH04 (1004) Wire Wound Type Power Inductor
R47 | 0.47 | ± 20% | 1MHz, 1V | 29 | 6.00 | 4.40 |
1R0 | 1.0 | ± 20% | 1MHz, 1V | 52 | 4.00 | 3.10 |
2R2 | 2.2 | ± 20% | 1MHz, 1V | 110 | 3.00 | 2.10 |
MLPH08 (1008) Wire Wound Type Power Inductor
Codes | Inductance (uH) | Tolerance | Test Condition | DCR (mΩ) max. | Isat (A) max. | Irms (A) max. |
---|---|---|---|---|---|---|
R47 | 0.47 | ± 20% | 1MHz, 1V | 22 | 6.20 | 4.90 |
1R0 | 1.0 | ± 20% | 1MHz, 1V | 44 | 4.30 | 3.30 |
2R2 | 2.2 | ± 20% | 1MHz, 1V | 89 | 3.20 | 2.20 |
Operating Temperature range: -40°C to +125°C
Electrical Performance Test
Item | Requirement | Test Method |
---|---|---|
Inductance | Refer to standard electrical characteristic spec. | HP4285A |
DC Resistance RDC | micro-ohm meter. | |
Isat | DC current will cause a 30% inductance reduction form initial value. | |
Irms | DC current will cause coil temp. rising to 40℃ whichever is smaller. |
Mechanical Performance Test
Item | Requirement | Test Method |
---|---|---|
Resistance to Soldering Heat | Appearance: No damage More than 95% of the terminal. Electrode should be covered with solder. Inductance: within ± 20% of initial value |
Flux: Rosin Solder Temperature: 260 ± 5°C Immersion Time: 10 ± 1 sec. |
Adhesive Test | No mechanical damage Soldering the products on PCB after the pulling test force>5N |
Reflow temperature: 245°C it shall be soldered on the substrate applying direction parallel to the substrate Apply force(F): 5 N Test time: 10 sec |
Temperature Cycle | No mechanical damage Inductance: within ± 20% of initial value |
Temperature: -50 ~ 125°C for 30 minutes each Cycle: 500cycles Measurement: at ambient temperature 24 hours after test completion |
Dry Heat Test | Temperature: 85 ± 2°C Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion |
|
Humidity Test | Temperature: 60 ± 2°C, Humidity: 90 ~ 95% RH Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion |
☑Storage Temperature: 5~40°C ; Humidity:<65%RH
Recommendable Reflow Soldering
Reel Specifications (Unit: mm)
Type | A | B | C | W | T | Quantity (EA) | ![]() |
---|---|---|---|---|---|---|---|
MLP03 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP05 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP(H)06 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP(H)04 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP(H)08 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP10 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 |
Tape Specifications (Unit: mm)
Type | A0 | B0 | K0 | t | ![]() |
---|---|---|---|---|---|
MLP03 | 1.45 ± 0.10 | 2.20 ± 0.10 | 1.12 ± 0.10 | 0.22 ± 0.05 | |
MLP05 | 1.45 ± 0.10 | 2.20 ± 0.10 | 1.12 ± 0.10 | 0.22 ± 0.05 | |
MLP06 | 1.80 ± 0.10 | 2.20 ± 0.10 | 1.15 ± 0.10 | 0.22 ± 0.05 | |
MLPH06 | 1.82 ± 0.05 | 2.23 ± 0.05 | 1.15 ± 0.05 | 0.22 ± 0.05 | |
MLP04 | 2.50 ± 0.10 | 3.00 ± 0.10 | 1.60 ± 0.10 | 0.25 ± 0.05 | |
MLPH04 | 2.25 ± 0.05 | 2.80 ± 0.10 | 1.35 ± 0.10 | 0.22 ± 0.05 | |
MLP08 | 2.50 ± 0.10 | 3.00 ± 0.10 | 1.60 ± 0.10 | 0.25 ± 0.05 | |
MLPH08 | 2.25 ± 0.05 | 2.80 ± 0.10 | 1.35 ± 0.10 | 0.22 ± 0.05 | |
MLP10 | 2.80 ± 0.10 | 3.45 ± 0.10 | 1.34 ± 0.10 | 0.23 ± 0.05 |
Resistor de precisión de película delgada 0.01%, TC2ppm, wirebondale, anti-corrosión, MELF. Sensado...
Lee masInductores cerámicos de alta frecuencia, tamaño pequeño hasta 01005. Inductor de película delgada,...
Lee masEl condensador cerámico multicapa ofrece alta tensión, alta frecuencia, bajo ruido, alta Q, baja TCR....
Lee mas