![APLICAÇÕES AUTOMOTIVAS](https://cdn.ready-market.com.tw/cdb12976/Templates/pic/m/Promotion-Application-01.jpg?v=34c833ab)
APLICAÇÕES AUTOMOTIVAS
Resistor de precisão de filme fino 0,01%, TC2ppm, wirebondale, anti-corrosivo, MELF. Detecção de corrente,...
consulte Mais informaçãoIndutor de chip de ferrite enrolado em fio, alta potência, tamanhos pequenos, circuito magnético fechado evita interferência, adequado para instalação de alta densidade e soldagem por refluxo. Usado em todos os tipos de dispositivos eletrônicos, computação, conversores.
MLP Series0806 ±20% 2.2μH 0.14 Ω 2.45A 2A
Tamanho | Tolerância | Indutância | Condição de teste | DCR (Ω) máximo. | I sat (A) máximo | I rms (A) máximo |
---|---|---|---|---|---|---|
0806 | ±20% | 2.2 | 1MHz, 1mA | 0.14 | 2.45 | 2 |
MLPH06 (0806) Wire Wound Type Power Inductor
Codes | Inductance (uH) | Tolerance | Test Condition | DCR (mΩ) max. | Isat (A) max. | Irms (A) max. |
---|---|---|---|---|---|---|
R47 | 0.47 | ± 20% | 1MHz, 1V | 30 | 5.30 | 4.05 |
1R0 | 1.0 | ± 20% | 1MHz, 1V | 60 | 3.30 | 3.00 |
1R5 | 1.5 | ± 20% | 1MHz, 1V | 99 | 3.10 | 2.20 |
2R2 | 2.2 | ± 20% | 1MHz, 1V | 140 | 2.45 | 2.00 |
MLPH04 (1004) Wire Wound Type Power Inductor
R47 | 0.47 | ± 20% | 1MHz, 1V | 29 | 6.00 | 4.40 |
1R0 | 1.0 | ± 20% | 1MHz, 1V | 52 | 4.00 | 3.10 |
2R2 | 2.2 | ± 20% | 1MHz, 1V | 110 | 3.00 | 2.10 |
MLPH08 (1008) Wire Wound Type Power Inductor
Codes | Inductance (uH) | Tolerance | Test Condition | DCR (mΩ) max. | Isat (A) max. | Irms (A) max. |
---|---|---|---|---|---|---|
R47 | 0.47 | ± 20% | 1MHz, 1V | 22 | 6.20 | 4.90 |
1R0 | 1.0 | ± 20% | 1MHz, 1V | 44 | 4.30 | 3.30 |
2R2 | 2.2 | ± 20% | 1MHz, 1V | 89 | 3.20 | 2.20 |
Operating Temperature range: -40°C to +125°C
Electrical Performance Test
Item | Requirement | Test Method |
---|---|---|
Inductance | Refer to standard electrical characteristic spec. | HP4285A |
DC Resistance RDC | micro-ohm meter. | |
Isat | DC current will cause a 30% inductance reduction form initial value. | |
Irms | DC current will cause coil temp. rising to 40℃ whichever is smaller. |
Mechanical Performance Test
Item | Requirement | Test Method |
---|---|---|
Resistance to Soldering Heat | Appearance: No damage More than 95% of the terminal. Electrode should be covered with solder. Inductance: within ± 20% of initial value |
Flux: Rosin Solder Temperature: 260 ± 5°C Immersion Time: 10 ± 1 sec. |
Adhesive Test | No mechanical damage Soldering the products on PCB after the pulling test force>5N |
Reflow temperature: 245°C it shall be soldered on the substrate applying direction parallel to the substrate Apply force(F): 5 N Test time: 10 sec |
Temperature Cycle | No mechanical damage Inductance: within ± 20% of initial value |
Temperature: -50 ~ 125°C for 30 minutes each Cycle: 500cycles Measurement: at ambient temperature 24 hours after test completion |
Dry Heat Test | Temperature: 85 ± 2°C Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion |
|
Humidity Test | Temperature: 60 ± 2°C, Humidity: 90 ~ 95% RH Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion |
☑Storage Temperature: 5~40°C ; Humidity:<65%RH
Recommendable Reflow Soldering
Reel Specifications (Unit: mm)
Type | A | B | C | W | T | Quantity (EA) | ![]() |
---|---|---|---|---|---|---|---|
MLP03 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP05 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP(H)06 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP(H)04 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP(H)08 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
MLP10 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 |
Tape Specifications (Unit: mm)
Type | A0 | B0 | K0 | t | ![]() |
---|---|---|---|---|---|
MLP03 | 1.45 ± 0.10 | 2.20 ± 0.10 | 1.12 ± 0.10 | 0.22 ± 0.05 | |
MLP05 | 1.45 ± 0.10 | 2.20 ± 0.10 | 1.12 ± 0.10 | 0.22 ± 0.05 | |
MLP06 | 1.80 ± 0.10 | 2.20 ± 0.10 | 1.15 ± 0.10 | 0.22 ± 0.05 | |
MLPH06 | 1.82 ± 0.05 | 2.23 ± 0.05 | 1.15 ± 0.05 | 0.22 ± 0.05 | |
MLP04 | 2.50 ± 0.10 | 3.00 ± 0.10 | 1.60 ± 0.10 | 0.25 ± 0.05 | |
MLPH04 | 2.25 ± 0.05 | 2.80 ± 0.10 | 1.35 ± 0.10 | 0.22 ± 0.05 | |
MLP08 | 2.50 ± 0.10 | 3.00 ± 0.10 | 1.60 ± 0.10 | 0.25 ± 0.05 | |
MLPH08 | 2.25 ± 0.05 | 2.80 ± 0.10 | 1.35 ± 0.10 | 0.22 ± 0.05 | |
MLP10 | 2.80 ± 0.10 | 3.45 ± 0.10 | 1.34 ± 0.10 | 0.23 ± 0.05 |
Resistor de precisão de filme fino 0,01%, TC2ppm, wirebondale, anti-corrosivo, MELF. Detecção de corrente,...
consulte Mais informaçãoIndutores de chip cerâmico de alta frequência, tamanho pequeno até 01005. Indutor de filme fino, multicamada,...
consulte Mais informaçãoO capacitor cerâmico multicamada oferece alta tensão, alta frequência, baixo ruído, alta Q, baixo...
consulte Mais informação