APLICACIONES AUTOMOTRICES
Resistor de precisión de película delgada 0.01%, TC2ppm, con cable de unión, anticorrosivo, MELF. Detección...
Lee masInductor de Chip de Ferrita Multicapa (Serie ML ML03KT2R7)
ML03KT2R7
Inductor de chip de ferrita multicapa, tamaños pequeños, circuito magnético cerrado que evita la diafonía, adecuado para instalación de alta densidad y soldadura de reflujo. Utilizado en todo tipo de dispositivos electrónicos, informática, convertidores.
ML Series0603 ±10%nH 2700μH 1.35 Ω 15mA 35 40MHz 10MHz, 200mV MHz
| Tamaño | Tolerancia | Inductancia | DCR (Ω) máx. | IDC (mA) | Q | SRF | Frecuencia L/Q (MHz) |
|---|---|---|---|---|---|---|---|
| 0603 | ±10% | 2700 | 1.35 | 15 | 35 | 40MHz | 10MHz, 200mV |
Especificaciones eléctricas de alta corriente
MLH05 Multilayer Ferrite Chip Inductors Type(□:Tolerance):
| Part No. | Inductance (uH) | Tolerance | Test Freq. | SRF (MHz) min. | DCR (Ω) max. | IDC (mA) max. |
|---|---|---|---|---|---|---|
| MLH05□TR47 | 0.47 | ± 20% | 1MHz, 250mV | 100 | 0.125 | 1100 |
| MLH05□TR68 | 0.68 | ± 20% | 1MHz, 250mV | 100 | 0.150 | 1000 |
| MLH05□TR82 | 0.82 | ± 20% | 1MHz, 250mV | 90 | 0.175 | 900 |
| MLH05□T1R0 | 1.0 | ± 20% | 1MHz, 250mV | 90 | 0.200 | 800 |
| MLH05□T1R2 | 1.2 | ± 20% | 1MHz, 250mV | 80 | 0.200 | 800 |
| MLH05□T1R5 | 1.5 | ± 20% | 1MHz, 250mV | 70 | 0.275 | 700 |
| MLH05□T1R8 | 1.8 | ± 20% | 1MHz, 250mV | 60 | 0.275 | 700 |
| MLH05□T2R2 | 2.2 | ± 20% | 1MHz, 250mV | 50 | 0.313 | 600 |
| MLH05□T3R3 | 3.3 | ± 20% | 1MHz, 250mV | 40 | 0.275 | 500 |
| MLH05□T4R7 | 4.7 | ± 20% | 1MHz, 250mV | 30 | 0.375 | 500 |
☑ Operating temperature range: -40 ~ +125°C
MLH06 Multilayer Ferrite Chip Inductors Type(□:Tolerance):
| Part No. | Inductance (uH) | Tolerance | Test Freq. | SRF (MHz) min. | DCR (Ω) max. | IDC (mA) max. |
|---|---|---|---|---|---|---|
| MLH06□TR47 | 0.47 | ± 20% | 1MHz, 250mV | 100 | 0.182 | 1500 |
| MLH06□TR68 | 0.68 | ± 20% | 1MHz, 250mV | 90 | 0.195 | 1500 |
| MLH06□TR82 | 0.82 | ± 20% | 1MHz, 250mV | 80 | 0.208 | 1500 |
| MLH06□T1R0 | 1.0 | ± 20% | 1MHz, 250mV | 60 | 0.208 | 1400 |
| MLH06□T1R2 | 1.2 | ± 20% | 1MHz, 250mV | 60 | 0.208 | 1400 |
| MLH06□T1R5 | 1.5 | ± 20% | 1MHz, 250mV | 50 | 0.260 | 1200 |
| MLH06□T1R8 | 1.8 | ± 20% | 1MHz, 250mV | 50 | 0.260% | 1200 |
| MLH06□T2R2 | 2.2 | ± 20% | 1MHz, 250mV | 40 | 0.286 | 1200 |
| MLH06□T3R3 | 3.3 | ± 20% | 1MHz, 250mV | 30 | 0.312 | 1100 |
| MLH06□T4R7 | 4.7 | ± 20% | 1MHz, 250mV | 20 | 0.390 | 1100 |
☑ Operating temperature range: -40 ~ +125°C
MLH08 Multilayer Ferrite Chip Inductors Type(□:Tolerance):
| Part No. | Inductance (uH) | Tolerance | Test Freq. | SRF (MHz) min. | DCR (Ω) max. | IDC (mA) max. |
|---|---|---|---|---|---|---|
| MLH08□TR47 | 0.47 | ± 20% | 1MHz, 250mV | 100 | 0.088 | 1800 |
| MLH08□TR68 | 0.68 | ± 20% | 1MHz, 250mV | 90 | 0.113 | 1700 |
| MLH08□TR82 | 0.82 | ± 20% | 1MHz, 250mV | 80 | 0.125 | 1700 |
| MLH08□T1R0 | 1.0 | ± 20% | 1MHz, 250mV | 60 | 0.138 | 1600 |
| MLH08□T1R2 | 1.2 | ± 20% | 1MHz, 250mV | 60 | 0.138 | 1600 |
| MLH08□T1R5 | 1.5 | ± 20% | 1MHz, 250mV | 50 | 0.163 | 1500 |
| MLH08□T1R8 | 1.8 | ± 20% | 1MHz, 250mV | 50 | 0.163 | 1500 |
| MLH08□T2R2 | 2.2 | ± 20% | 1MHz, 250mV | 40 | 0.213 | 1300 |
| MLH08□T3R3 | 3.3 | ± 20% | 1MHz, 250mV | 30 | 0.200 | 1200 |
| MLH08□T4R7 | 4.7 | ± 20% | 1MHz, 250mV | 25 | 0.250 | 1100 |
☑ Operating temperature range: -40 ~ +125°C
Características Ambientales
Electrical Performance Test
| Item | Requirement | Test Method |
|---|---|---|
| Inductance | Refer to standard electrical characteristic spec. | HP4291B |
| Q | HP4291B | |
| SRF | HP4291B | |
| DC Resistance RDC | Agilent 34401A |
Mechanical Performance Test
| Item | Requirement | Test Method |
|---|---|---|
| Resistance to Soldering Heat | Appearance: No damage More than 75% of the terminal. Electrode should be covered with solder. |
Pre-heating: 150°C, 1min. Solder Composition: Sn/Ag3.0/Cu0.5 (Pb-Free) Solder Temperature: 260± 5°C (Pb-Free) Immersion Time: 10± 1 sec. |
| Solderability | The electrodes shall be at least 90% covered with new solder coating | Pre-heating: 150°C, 1min. Solder Composition: Sn/Ag3.0/Cu0.5 (Pb-Free) Solder Temperature: 245± 5°C (Pb-Free) Immersion Time: 4± 1 sec. |
| Flexure Strength | The forces applied on the right conditions must not damage the terminal electrode and the ferrite. |  Test device shall be soldered on the substrate |
| Vibration | Test device shall be soldered on the substrate Oscillation Frequency: 10 to 55 to 10Hz for 1 min. Amplitude: 1.5 mm Time: 2 hrs for each axis (X, Y & Z), total 6 hrs |
Climatic Test
| Item | Requirement | Test Method | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Damp Heat with Load | Appearance: No damage L change: within± 20% of initial value |
Temperature: 40± 2°C Relative Humidity: 90 ~ 95% Time: 1000 hrs Measured after exposure in the room condition for 24 hrs |
||||||||||||||
| Temperature Cycle | One cycle:
Total: 100 cycles |
|||||||||||||||
| High Temperature Resistance | Temperature: 85± 3°C Relative Humidity: 20% Applied Current: Rated Current Time: 1000 hrs Measured after exposure in the room condition for 24 hrs |
|||||||||||||||
| Low Temperature Resistance | Temperature: -40± 3°C Relative Humidity: 0% Time: 1000 hrs Measured after exposure in the room condition for 24 hrs |
☑ Storage Temperature: 15 ~ 28°C; Humidity < 80%RH
Embalaje
Reel Specifications (Unit : mm)
| Type | A | B | C | W | T | Quantity (EA) | |
|---|---|---|---|---|---|---|---|
| Paper Tape (Type B) | Polystyrene Tape (Type A) | ||||||
| ML03 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 4,000 | - |
| ML05 (≤ 2.2uH) | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 4,000 | - |
| ML05 (≥ 2.7uH) | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | - | 3,000 |
| ML06 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | - | 3,000 |
| MLH05 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 4.000 | - |
| MLH06 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | - | 3,000 |
| MLH08 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | - | 3,000 |
Tape Specifications & Tape Material (Unit : mm)
| Type | A | B | T | W | P | F | K | Tape Type |
|---|---|---|---|---|---|---|---|---|
| ML03 | 1.05 | 1.85 | 0.95 | 8.0 | 4.0 | 3.5 | - | B |
| ML05(≤ 2.2uH) | 1.50 | 2.42 | 0.95 | 8.0 | 4.0 | 3.5 | - | B |
| ML05(≥ 2.7uH) | 1.50 | 2.35 | 1.45 | 8.0 | 4.0 | 3.5 | 0.22 | A |
| ML06 | 1.88 | 3.50 | 1.27 | 8.0 | 4.0 | 3.5 | 0.22 | A |
| MLH05 | 1.45 | 2.25 | 0.95 | 8.0 | 4.0 | 3.5 | - | B |
| MLH06 | 1.88 | 2.40 | 1.23 | 8.0 | 4.0 | 3.5 | 0.23 | A |
| MLH08 | 2.20 | 2.85 | 1.40 | 8.0 | 4.0 | 3.5 | 0.23 | A |
Note:
1. Please make sure that your product is has been evaluated and confirmed against your specifications when our product is mounted to your product.
2. Do not knock nor drop.
3. All the items and parameters in this product specification have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment agreed upon between you and us. You are requested not to use our product deviating from such agreement.
- Descarga de Archivos
-
-
Producto Principal
APLICACIONES MÉDICAS
Inductores de chip de alta frecuencia cerámicos, tamaño pequeño hasta 01005. Película delgada, multicapa,...
Lee mas
APLICACIONES DE COMUNICACIÓN
El capacitor cerámico multicapa ofrece alta tensión, alta frecuencia, bajo ruido, alto Q, baja TCR....
Lee mas