AUTOMOTIVE-ANWENDUNGEN
Dünnschicht-Präzisionswiderstand 0,01%, TC2ppm, Drahtbondage, Anti-Korrosiv, MELF. Stromerfassung,...
WeiterlesenSMD-Leistungsdrossel (PCD-Serie PCD0503KT390)
PCD0503KT390
SMD Hochleistungs-, Hochsättigungsinduktoren, silberbeschichteter Typ, kostengünstiges Design, ideale Induktoren für DC-DC-Wandler, verschiedene Größen von kleiner Größe von 3,5*3 bis 10*9mm.
PCD Series0503 ±10% 39μH 0.42 Ω 1A
| Größe | Toleranz | Induktivität | Testbedingung | DCR (Ω) max. | IDC (A) |
|---|---|---|---|---|---|
| 0503 | ±10% | 39 | 1KHz, 0.25V | 0.42 | 1 |
Band- und Spulenspezifikationen (Einheit: mm)
| Type | Tape Size | Parts Per Reel | |
|---|---|---|---|
| W | P | 13" | |
| PCD0301 | 12 | 8 | 3000 |
| PCD0302 | 12 | 8 | 2000 |
| PCD0403 | 12 | 8 | 1500 |
| PCD0502 | 12 | 8 | 2000 |
| PCD0503 | 12 | 8 | 1500 |
| PCD0504 | 12 | 8 | 1500 |
| PCD0703 | 16 | 12 | 1000 |
| PCD0705 | 16 | 12 | 1000 |
| PCD1004 | 24 | 12 | 1000 |
| PCD1005 | 24 | 12 | 500 |
| PCD1006 | 24 | 12 | 500 |
Umweltspezifikationen für SMT-Leistungsdrosseln
General
| Item | Specification |
|---|---|
| Shelf Storage conditions | Temperature range: 15 ~ 28°C; Humidity: < 80% relative humidity. Recommended product should be used within one year from the time of delivery. |
Environmental Test
| Item | Specification | Test Conditions / Test Methods |
|---|---|---|
| High temperature Storage test | No case deformation or change in appearance. Δ L/L ≤10% |
Temperature 85 ± 2°C, Time: 48 ± 2 hours, Tested after 1hour at room temperature. |
| Low temperature Storage test | Temperature -25 ± 2°C, Time: 48 ± 2 hours, Tested after 1hour at room temperature. |
|
| Humidity test | Temperature 40 ± 2°C, 90~95% relative humidity Time: 96 ± 2 hours Tested after 1hour at room temperature. |
|
| Thermal shock test | First -25°C 30minutes then 25°C 10 minutes last 85°C 30 minutes, as 1 cycle. Go through 5 cycles. Tested after 1 hour at room temperature. |
Mechanical Test
| Item | Specification | Test Conditions / Test Methods |
|---|---|---|
| Solderability test | Terminal area must have 90% minimum solder coverage. | Dip pads in flux then dip in solder pot (SnCuNi) at 245 ± 5°C for 3 seconds. |
| Resistance to Soldering Heat | No case deformation or change in appearance. | Flux should cover the whole of the sample before heating, then be preheated for about 2 minutes over temperature of 130 ~ 150°C. Immersing to 260 ± 5°C for 10 seconds. |
| Vibration test | No case deformation or change in appearance. Δ L/L ≤10% |
Apply frequency 10 ~ 55Hz. 1.5mm amplitude in each of perpendicular direction for 2 hours. |
| Shock resistance | Drop down with 981m/s² (100G) shock attitude upon a rubber block method shock testing machine, for 1 time. In each of three orientations. |
Reflow
The Condition Of Reflow (Recommendation):
Code
- 390
- Dateien herunterladen
-
-
Hauptprodukt
MEDIZINISCHE ANWENDUNGEN
Keramik-Hochfrequenz-Chip-Drosseln, kleine Größe bis 01005. Dünnschicht-, Mehrschicht-, Wickeldrossel,...
Weiterlesen
KOMMUNIKATIONSANWENDUNGEN
Mehrschichtige Keramikkondensatoren bieten hohe Spannung, hohe Frequenz, geringes Rauschen, hohen Q-Faktor,...
Weiterlesen