와이어 와운드 타입 전력 인덕터
MLP08MTR47
와이어 와운드 페라이트 칩 고출력 인덕터, 소형 사이즈, 폐쇄 자기 회로로 크로스토크 방지, 고밀도 설치 및 리플로우 솔더링에 적합. 모든 종류의 전자 기기, 컴퓨팅, 컨버터에서 사용됩니다.
MLP Series1008 ±20% 0.47μH 0.025 Ω 4.95A 4.18A
| 크기 | 허용오차 | 인덕턴스 | 테스트 조건 | DCR (Ω) 최대. | I sat (A) 최대. | I rms (A) 최대. |
|---|---|---|---|---|---|---|
| 1008 | ±20% | 0.47 | 1MHz, 1mA | 0.025 | 4.95 | 4.18 |
고전류 전기 사양
MLPH06 (0806) Wire Wound Type Power Inductor
| Codes | Inductance (uH) | Tolerance | Test Condition | DCR (mΩ) max. | Isat (A) max. | Irms (A) max. |
|---|---|---|---|---|---|---|
| R47 | 0.47 | ± 20% | 1MHz, 1V | 30 | 5.30 | 4.05 |
| 1R0 | 1.0 | ± 20% | 1MHz, 1V | 60 | 3.30 | 3.00 |
| 1R5 | 1.5 | ± 20% | 1MHz, 1V | 99 | 3.10 | 2.20 |
| 2R2 | 2.2 | ± 20% | 1MHz, 1V | 140 | 2.45 | 2.00 |
MLPH04 (1004) Wire Wound Type Power Inductor
| R47 | 0.47 | ± 20% | 1MHz, 1V | 29 | 6.00 | 4.40 |
| 1R0 | 1.0 | ± 20% | 1MHz, 1V | 52 | 4.00 | 3.10 |
| 2R2 | 2.2 | ± 20% | 1MHz, 1V | 110 | 3.00 | 2.10 |
MLPH08 (1008) Wire Wound Type Power Inductor
| Codes | Inductance (uH) | Tolerance | Test Condition | DCR (mΩ) max. | Isat (A) max. | Irms (A) max. |
|---|---|---|---|---|---|---|
| R47 | 0.47 | ± 20% | 1MHz, 1V | 22 | 6.20 | 4.90 |
| 1R0 | 1.0 | ± 20% | 1MHz, 1V | 44 | 4.30 | 3.30 |
| 2R2 | 2.2 | ± 20% | 1MHz, 1V | 89 | 3.20 | 2.20 |
Operating Temperature range: -40°C to +125°C
환경 특성
Electrical Performance Test
| Item | Requirement | Test Method |
|---|---|---|
| Inductance | Refer to standard electrical characteristic spec. | HP4285A |
| DC Resistance RDC | micro-ohm meter. | |
| Isat | DC current will cause a 30% inductance reduction form initial value. | |
| Irms | DC current will cause coil temp. rising to 40℃ whichever is smaller. |
Mechanical Performance Test
| Item | Requirement | Test Method |
|---|---|---|
| Resistance to Soldering Heat | Appearance: No damage More than 95% of the terminal. Electrode should be covered with solder. Inductance: within ± 20% of initial value |
Flux: Rosin Solder Temperature: 260 ± 5°C Immersion Time: 10 ± 1 sec. |
| Adhesive Test | No mechanical damage Soldering the products on PCB after the pulling test force>5N |
Reflow temperature: 245°C it shall be soldered on the substrate applying direction parallel to the substrate Apply force(F): 5 N Test time: 10 sec |
| Temperature Cycle | No mechanical damage Inductance: within ± 20% of initial value |
Temperature: -50 ~ 125°C for 30 minutes each Cycle: 500cycles Measurement: at ambient temperature 24 hours after test completion |
| Dry Heat Test | Temperature: 85 ± 2°C Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion |
|
| Humidity Test | Temperature: 60 ± 2°C, Humidity: 90 ~ 95% RH Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion |
☑Storage Temperature: 5~40°C ; Humidity:<65%RH
리플로우
Recommendable Reflow Soldering
포장
Reel Specifications (Unit: mm)
| Type | A | B | C | W | T | Quantity (EA) |  |
|---|---|---|---|---|---|---|---|
| MLP03 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
| MLP05 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
| MLP(H)06 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
| MLP(H)04 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
| MLP(H)08 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 | |
| MLP10 | 178 ± 1 | 60.0 + 0.5 | 13.0 ± 0.2 | 9.00 ± 0.5 | 12.0 ± 0.15 | 3,000 |
Tape Specifications (Unit: mm)
| Type | A0 | B0 | K0 | t |  |
|---|---|---|---|---|---|
| MLP03 | 1.45 ± 0.10 | 2.20 ± 0.10 | 1.12 ± 0.10 | 0.22 ± 0.05 | |
| MLP05 | 1.45 ± 0.10 | 2.20 ± 0.10 | 1.12 ± 0.10 | 0.22 ± 0.05 | |
| MLP06 | 1.80 ± 0.10 | 2.20 ± 0.10 | 1.15 ± 0.10 | 0.22 ± 0.05 | |
| MLPH06 | 1.82 ± 0.05 | 2.23 ± 0.05 | 1.15 ± 0.05 | 0.22 ± 0.05 | |
| MLP04 | 2.50 ± 0.10 | 3.00 ± 0.10 | 1.60 ± 0.10 | 0.25 ± 0.05 | |
| MLPH04 | 2.25 ± 0.05 | 2.80 ± 0.10 | 1.35 ± 0.10 | 0.22 ± 0.05 | |
| MLP08 | 2.50 ± 0.10 | 3.00 ± 0.10 | 1.60 ± 0.10 | 0.25 ± 0.05 | |
| MLPH08 | 2.25 ± 0.05 | 2.80 ± 0.10 | 1.35 ± 0.10 | 0.22 ± 0.05 | |
| MLP10 | 2.80 ± 0.10 | 3.45 ± 0.10 | 1.34 ± 0.10 | 0.23 ± 0.05 |
코드
- R47
- 파일 다운로드
-
-
주요 제품
