APLICACIONES AUTOMOTRICES
Resistor de precisión de película delgada 0.01%, TC2ppm, con cable de unión, anticorrosivo, MELF. Detección...
Lee masInductor de alimentación SMD blindado (Serie PCDR PCDR1045MT150)
PCDR1045MT150
Inductor de potencia SMD blindado, compacto, de perfil bajo con baja resistencia en serie y alta corriente, con blindaje magnético contra la radiación.
PCDR Series1045 ±20% 15μH 0.047 Ω 2.4A
| Tamaño | Tolerancia | Inductancia | Condición de prueba | DCR (Ω) máx. | IDC (A) |
|---|---|---|---|---|---|
| 1045 | ±20% | 15 | 1KHz, 0.5V | 0.047 | 2.4 |
Especificaciones de cinta y carrete (Unidad: mm)
| Type | Tape Size | Parts Per Reel | |
|---|---|---|---|
| W | P | 13" | |
| PCDR0628 | 16 | 12 | 1000 |
| PCDR0728 | 16 | 12 | 1000 |
| PCDR0730 | 16 | 12 | 1000 |
| PCDR0732 | 16 | 12 | 1000 |
| PCDR0745 | 16 | 12 | 1000 |
| PCDR1045 | 24 | 16 | 750 |
| PCDR1255 | 24 | 16 | 500 |
| PCDR1265 | 24 | 16 | 500 |
| PCDR1275 | 24 | 16 | 350 |
Especificaciones Ambientales del Inductor de Potencia SMD
General
| Item | Specification |
|---|---|
| Shelf Storage conditions | Temperature range: 15 ~ 28°C; Humidity: < 80% relative humidity. Recommended product should be used within 12 months from the time of delivery. |
Environmental Test
| Item | Specification | Test Conditions / Test Methods |
|---|---|---|
| High temperature Storage test | No case deformation or change in appearance. Δ L/L ≤10% | Temperature 85 ± 2°C, Time: 48 ± 2 hours, Tested after 1hour at room temperature. |
| Low temperature Storage test | Temperature -40 ± 2°C, Time: 48 ± 2 hours, Tested after 1hour at room temperature. | |
| Humidity test | Temperature 40 ± 2°C, 90 ~ 95% relative humidity Time: 96 ± 2 hours Tested after 1hour at room temperature. | |
| Thermal shock test | First -25°C 30minutes then 25°C 10 minutes last 85°C 30 minutes, as 1 cycle. Go through 5 cycles. Tested after 1 hour at room temperature. |
Mechanical Test
| Item | Specification | Test Conditions / Test Methods |
|---|---|---|
| Solderability test | Terminal area must have 90% minimum solder coverage. | Product with Lead-free terminal: Dip pads in flux then dip in solder pot at 245 ± 5°C for 3 seconds. |
| Resistance to Soldering Heat | No case deformation or change in appearance. | Flux should cover the whole of the sample before heating, then be preheated for about 2 minutes over temperature of 130 ~ 150°C. Immersing to 260 ± 5°C for 10 seconds. |
| Vibration test | No case deformation or change in appearance. Δ L/L ≤10% | Apply frequency 10 ~ 55Hz. 1.5mm amplitude in each of perpendicular direction for 2 hours. |
| Shock resistance | Drop down with 981m/s² (100G) shock attitude upon a rubber block method shock testing machine, for 1 time. In each of three orientations. |
Reflujo
The Condition Of Reflow (Recommendation):
Código
- 150
- Descarga de Archivos
Producto Principal
APLICACIONES MÉDICAS
Inductores de chip de alta frecuencia cerámicos, tamaño pequeño hasta 01005. Película delgada, multicapa,...
Lee mas
APLICACIONES DE COMUNICACIÓN
El capacitor cerámico multicapa ofrece alta tensión, alta frecuencia, bajo ruido, alto Q, baja TCR....
Lee mas