Wire Wound Type Power Inductor Manufacturers

Wire Wound Type Power Inductor

Send Inquiry Add to List

MLP08MT1R5

Wire Wound Type Power Inductor Files Download

Wirewound ferrite chip high power inductor , small sizes , closed magnetic circuit avoids crosstalk , suitable for high density installation and re-flow soldering. Used in all kind electronic devices, computing, converters.
MLP Series1008 ±20% 1.5μH 0.077 Ω 2.91A 2.27A

Size	Tolerance	Inductance	Test Condition	DCR (Ω) max.	I sat (A) max.	I rms (A) max.
1008	±20%	1.5	1MHz, 1mA	0.077	2.91	2.27

High Current Electrical Specifications

MLPH06 (0806) Wire Wound Type Power Inductor

Codes	Inductance (uH)	Tolerance	Test Condition	DCR (mΩ) max.	Isat (A) max.	Irms (A) max.
R47	0.47	± 20%	1MHz, 1V	30	5.30	4.05
1R0	1.0	± 20%	1MHz, 1V	60	3.30	3.00
1R5	1.5	± 20%	1MHz, 1V	99	3.10	2.20
2R2	2.2	± 20%	1MHz, 1V	140	2.45	2.00

MLPH04 (1004) Wire Wound Type Power Inductor

R47	0.47	± 20%	1MHz, 1V	29	6.00	4.40
1R0	1.0	± 20%	1MHz, 1V	52	4.00	3.10
2R2	2.2	± 20%	1MHz, 1V	110	3.00	2.10

MLPH08 (1008) Wire Wound Type Power Inductor

Codes	Inductance (uH)	Tolerance	Test Condition	DCR (mΩ) max.	Isat (A) max.	Irms (A) max.
R47	0.47	± 20%	1MHz, 1V	22	6.20	4.90
1R0	1.0	± 20%	1MHz, 1V	44	4.30	3.30
2R2	2.2	± 20%	1MHz, 1V	89	3.20	2.20

Operating Temperature range: -40°C to +125°C

Environmental Characteristics

Electrical Performance Test

Item	Requirement	Test Method
Inductance	Refer to standard electrical characteristic spec.	HP4285A
DC Resistance RDC		micro-ohm meter.
Isat		DC current will cause a 30% inductance reduction form initial value.
Irms		DC current will cause coil temp. rising to 40℃ whichever is smaller.

Mechanical Performance Test

Item	Requirement	Test Method
Resistance to Soldering Heat	Appearance: No damage More than 95% of the terminal. Electrode should be covered with solder. Inductance: within ± 20% of initial value	Flux: Rosin Solder Temperature: 260 ± 5°C Immersion Time: 10 ± 1 sec.
Adhesive Test	No mechanical damage Soldering the products on PCB after the pulling test force>5N	Reflow temperature: 245°C it shall be soldered on the substrate applying direction parallel to the substrate Apply force(F): 5 N Test time: 10 sec
Temperature Cycle	No mechanical damage Inductance: within ± 20% of initial value	Temperature: -50 ~ 125°C for 30 minutes each Cycle: 500cycles Measurement: at ambient temperature 24 hours after test completion
Dry Heat Test		Temperature: 85 ± 2°C Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion
Humidity Test		Temperature: 60 ± 2°C, Humidity: 90 ~ 95% RH Testing time: 500 hrs Applied current: full rated current Measurement: at ambient temperature 24 hours after test completion

☑Storage Temperature: 5~40°C ; Humidity:<65%RH

Reflow

Recommendable Reflow Soldering

Packaging

Reel Specifications (Unit: mm)

Type	A	B	C	W	T	Quantity (EA)
MLP03	178 ± 1	60.0 + 0.5	13.0 ± 0.2	9.00 ± 0.5	12.0 ± 0.15	3,000
MLP05	178 ± 1	60.0 + 0.5	13.0 ± 0.2	9.00 ± 0.5	12.0 ± 0.15	3,000
MLP(H)06	178 ± 1	60.0 + 0.5	13.0 ± 0.2	9.00 ± 0.5	12.0 ± 0.15	3,000
MLP(H)04	178 ± 1	60.0 + 0.5	13.0 ± 0.2	9.00 ± 0.5	12.0 ± 0.15	3,000
MLP(H)08	178 ± 1	60.0 + 0.5	13.0 ± 0.2	9.00 ± 0.5	12.0 ± 0.15	3,000
MLP10	178 ± 1	60.0 + 0.5	13.0 ± 0.2	9.00 ± 0.5	12.0 ± 0.15	3,000

Tape Specifications (Unit: mm)

Type	A0	B0	K0	t
MLP03	1.45 ± 0.10	2.20 ± 0.10	1.12 ± 0.10	0.22 ± 0.05
MLP05	1.45 ± 0.10	2.20 ± 0.10	1.12 ± 0.10	0.22 ± 0.05
MLP06	1.80 ± 0.10	2.20 ± 0.10	1.15 ± 0.10	0.22 ± 0.05
MLPH06	1.82 ± 0.05	2.23 ± 0.05	1.15 ± 0.05	0.22 ± 0.05
MLP04	2.50 ± 0.10	3.00 ± 0.10	1.60 ± 0.10	0.25 ± 0.05
MLPH04	2.25 ± 0.05	2.80 ± 0.10	1.35 ± 0.10	0.22 ± 0.05
MLP08	2.50 ± 0.10	3.00 ± 0.10	1.60 ± 0.10	0.25 ± 0.05
MLPH08	2.25 ± 0.05	2.80 ± 0.10	1.35 ± 0.10	0.22 ± 0.05
MLP10	2.80 ± 0.10	3.45 ± 0.10	1.34 ± 0.10	0.23 ± 0.05

Code

Files Download

Data Sheet

Wire Wound Type Power Inductor - MLP Series

SEARCH

Condition search: Cross Search

Best Sale

Wire Wound Type Power Inductor Manufacturer - Viking

Based in Taiwan, Viking Tech Corporation is one of the prime Wire Wound Type Power Inductor manufacturers since 1997. And their products are used throughout automotive, electronic device applications, with manufacturing tolerance down to 0.01% and TCR down to 2 ppm in a broad range of package sizes.

TS16949/ ISO9001/ ISO14001 and meet AEC-Q200 standards, Viking has been offering anti-sulfur, anti-surge, pulse, high voltage, high power precision resistors including thin/ thick film resistors, automotive resistors, melf resistors, current sense resistors, etc. Low noise, low TC, high power inductors such as rf inductors, chip inductors, power inductors, variable inductors, ferrite chip inductors, shielded inductors, wire wound inductors and dip inductors.

Wire Wound Type Power Inductor has been offering customers high quality power resistors, power inductors and aluminum electrolytic capacitors with solid reputation. Both with advanced technology and 25 years of experience, Viking makes sure to meet each customer's demands.

View our quality products Power Inductor, Thin Film Chip Resistor, RF Inductor, Chip Resistor, current sense resistor, metal film, metal resistors, Thick film resistor, Chip Capacitor, Power Resistor and feel free to Contact Us.

Main Product

AUTOMOTIVE APPLICATIONS

Thin film Precision resistor 0.01%, TC2ppm, wirebondale, Anti-Crossive, MELF. Current sensing, Metal...

MEDICAL APPLICATIONS

Ceramic high frequency chip inductors, small size to 01005. Thin film, multilayer, wirewound , ferrite...

COMMUNICATION APPLICATIONS

Multilayer Ceramic capacitor offers high Voltage, high frequency, low noise, High Q, Low TCR. NPO, X7R,...

Wire Wound Type Power Inductor Manufacturers - Viking

Wire Wound Type Power Inductor