Chip Common Mode Choke (CM series CMH05MT261) Manufacturers

Chip Common Mode Choke (CM series CMH05MT261)

Send Inquiry Add to List

CMH05MT261

Chip Common Mode Choke (CM series CMH05MT261) Files Download

Chip common mode Filter is small chip inductor with ferrite core and two line types wire wounded. Highly effective in noise suppression high common mode impedance at noise band and low differential mode impedance at signal band , low differential mode impedance with high coupling factor. there is almost no distortion on high speed singal. tipically for EMI radiation noise suppression for any electronic devices.
CM Series0805 ±20% 260μH 0.4 Ω 300mA 125V 10MΩ min.

Size	Tolerance	Inductance	Test Condition	DCR (Ω) max.	IDC (mA)	Rated Voltage	Withstanding Voltage Vdc (V)	Insulation Resistance (MΩ) min.
0805	±20%	260	100MHz	0.4	300	50	125	10

Environmental Characteristics

Electrical Performance Test

Items	Requirement	Test Conditions / Test Methods
Impedance	Refer to standard electrical characteristic spec. Component should not be damaged	LCR Meter HP 4291B
DC Resistance DCR		Micro-Ohm meter (GOM-801G)
Withstand Voltage (VDC)		Test Voltage: 2.5 Times Rated Voltage Testing Time: 60 seconds Charge Current: 0.5mA
Rated Voltage (VDC)		Test Voltage: Rated Voltage Testing Time: 1 to 5 seconds Charge Current: 1mA
Insulation Resistance (I.R)		Charge Current: 1minute 10M ohm min.

Mechanical Performance Test

Items	Requirement	Test Conditions / Test Methods
Component Adhesion (Push Test)	Base: 0805≧2 Lbs Cover: 0805≧1 Lbs Base: 1206≧4 Lbs Cover: 1206≧2 Lbs	The component should be soldered (232°C± 5°C for 10 sec.) to tinned copper substrate Applied force gauge to the side of component It must withstand force of 2 or 4 pounds without failure of the component.
Drop	Component should not be damaged	Dropping chip by each side and corner. Drop 10 times in total Drop height: 100 cm Drop weight: 125 g
Solderability	The terminal should at least be 90% covered with solder	The component shall be dipped in a melted solder bath at 245 ±5℃ for 3 seconds
Vibration Test (Low Frequency)	Component should not be damaged	1. Amplitude: 1.5 m/m 2. Frequency: 10-55-10Hz (1min.) 3. Direction: X, Y, Z 4. Duration: 2 Hrs/X, Y, Z

Climatic Test

Items	Requirement	Test Conditions / Test Methods
Low Temperature Storage	Impedance change: Within± 20% Without distinct damage in appearance	1. Temp: -40 ±2°C 2. Time: 1000±48 Hours 3. Component should be tested after 1hour at room temperature
Thermal Shock		Total: 5 Cycles
High Temperature Storage		1. Temp: 85 ± 2°C 2. Time: 1000 ± 48 Hours 3. Component should be tested after 1hour at room temperature
Humidity		1. Temp: 40 ± 2°C 2. R.H. : 90 ~ 95% 3. Time: 48 ±2 Hours
High Temperature Load Life	There should be no evidence of short or open circuit	1. Temp: 85 ± 2°C 2. Time: 96 ± 12 Hours 3. Load: Allowed DC Current
Low Temperature Load Life	There should be no evidence of short or open circuit	1. Temp: -40 ± 2°C 2. Time: 96 ± 12 Hours 3. Load: Allowed DC Current

☑ Storage Temperature: 15~28°C; Humidity < 80%RH

Packaging

Packaging Quantity & Reel Specifications

Type	ΦA	ΦB	ΦC	W	T	Quantity (EA)
CMH05	178±2.0	60±0.5	13±0.3	9±0.3	11.4±1.0	2000
CMH06	178±2.0	60±0.5	13±0.3	9±0.3	11.4±1.0	2000

Embossed Plastic Tape Specifications

Type	A (mm)	B (mm)	W (mm)	E (mm)	F (mm)	P0 (mm)	P1 (mm)	P2 (mm)	ΦD0 (mm)	T (mm)
CMH05	1.40±0.10	2.55±0.05	8.0±0.20	1.75±0.10	3.5±0.10	4.00±0.10	4.00±0.10	2.00±0.10	1.50+0.10	1.35±0.10
CMH06	1.90±0.10	3.50±0.05	8.0±0.20	1.75±0.10	3.5±0.10	4.00±0.10	4.00±0.10	2.00±0.10	1.50+0.10	2.10±0.10

Peel-off Force

The force for tearing off cover tape is 0.05~0.69 (N) in the arrow direction at the following conditions:
Temperature: 5 ~ 35°C
Humidity: 45 ~ 85%
Atmospheric pressure: 860 ~ 1060hpa

Files Download

Data Sheet

Common Mode Filter - CM Series

SEARCH

Condition search: Cross Search

Best Sale

Chip Common Mode Choke (CM series CMH05MT261) Manufacturer - Viking

Based in Taiwan, Viking Tech Corporation is one of the prime Chip Common Mode Choke (CM series CMH05MT261) manufacturers since 1997. And their products are used throughout automotive, electronic device applications, with manufacturing tolerance down to 0.01% and TCR down to 2 ppm in a broad range of package sizes.

TS16949/ ISO9001/ ISO14001 and meet AEC-Q200 standards, Viking has been offering anti-sulfur, anti-surge, pulse, high voltage, high power precision resistors including thin/ thick film resistors, automotive resistors, melf resistors, current sense resistors, etc. Low noise, low TC, high power inductors such as rf inductors, chip inductors, power inductors, variable inductors, ferrite chip inductors, shielded inductors, wire wound inductors and dip inductors.

Chip Common Mode Choke (CM series CMH05MT261) has been offering customers high quality power resistors, power inductors and aluminum electrolytic capacitors with solid reputation. Both with advanced technology and 25 years of experience, Viking makes sure to meet each customer's demands.

View our quality products Power Inductor, Thin Film Chip Resistor, RF Inductor, Chip Resistor, current sense resistor, metal film, metal resistors, Thick film resistor, Chip Capacitor, Power Resistor and feel free to Contact Us.

Main Product

AUTOMOTIVE APPLICATIONS

Thin film Precision resistor 0.01%, TC2ppm, wirebondale, Anti-Crossive, MELF. Current sensing, Metal...

MEDICAL APPLICATIONS

Ceramic high frequency chip inductors, small size to 01005. Thin film, multilayer, wirewound , ferrite...

COMMUNICATION APPLICATIONS

Multilayer Ceramic capacitor offers high Voltage, high frequency, low noise, High Q, Low TCR. NPO, X7R,...

Chip Common Mode Choke (CM series CMH05MT261) Manufacturers - Viking

Chip Common Mode Choke (CM series CMH05MT261)