AUTOMOBILANWENDUNGEN
Dünnschicht-Präzisionswiderstand 0,01%, TC2ppm, Drahtbondable, Antikorrosiv, MELF. Stromsensoren, Metall,...
WeiterlesenPräzisions-Chip-Widerstand aus Aluminiumnitrid-Dünnschicht (ARN-Serie ARN03DTDU0820)
ARN03DTDU0820
Aluminiumnitrid-Dünnschicht-Präzisionschipwiderstand - ARN-Serie
ARN Series0603 ±0.5% 50 1/2W Series82Ω 5K/Reel
| Größe | Toleranz | TCR (ppm /℃) | Leistung | Widerstand (Ohm) | Verpackung |
|---|---|---|---|---|---|
| 0603 | ±0.5% | 50 | 1/2W | 82 | 5K/Reel |
Umwelteigenschaften
| Item | Requirement | Test Method |
|---|---|---|
| Temperature Coefficient of Resistance (T.C.R.) | As Spec. | MIL-STD-202 Method 304 +25/-55/+25/+125/+25°C |
| Short Time Overload(2) | ΔR±0.5% | Actual power handling capability is limited by the end user mounting process. As with any high power chip resistor the ability to remove the heat is critical to the overall performance of the device |
| Insulation Resistance | >9999 MΩ | MIL-STD-202 Method 302 Apply 100VDC for 1 minute |
| Endurance | ΔR±1% | MIL-STD-202 Method 108A 70±2°C, RCWV for 1000 hrs with 1.5 hrs “ON” and 0.5 hrs “OFF” |
| Damp Heat with Load | ΔR±0.4% | MIL-STD-202 Method 103B 40±2°C, 90~95% R.H. RCWV for 1000 hrs with 1.5 hrs “ON” and 0.5 hrs “OFF” |
| Solderability | 95% min. coverage | MIL-STD-202 Method 208H 245±5°C for 3 seconds |
| Resistance to Soldering Heat | ΔR±0.2% | MIL-STD-202 Method 210E 260±5°C for 10 seconds |
| Thermal Shock | ΔR±0.2% | MIL-STD-202 Method 107G -55°C ~155°C, 100 cycles |
| Low Temperature Operation | ΔR±0.2% | JIS-C-5201-1 4.36 1 hour, -65°C, followed by 45 minutes of RCWV |
| High Temperature Exposure | ΔR±0.2% | MIL-STD-202 Method 108 at 155°C for 1000 hrs |
RCWV(Rated continuous working voltage)= √(P*R) or Max. Operating voltage whichever is lower
☑ Storage Temperature: 15~28°C; Humidity < 80%RH
Lötbedingungen
(1) Time of IR reflow soldering at maximum temperature point 260°C：10s
(2) Time of wave soldering at maximum temperature point 260°C：10s
(3) Time of soldering iron at maximum temperature point 410°C：5s
Kennzeichnung
1206 / 2512: 4 digits marking
Example:
| Resistance | 500Ω | 2.2KΩ | 10KΩ | 12.5KΩ |
|---|---|---|---|---|
| Marking | 5000 | 2201 | 1002 | 1252 |
Verpackung
Packing Quantity & Reel Specifications (Unit :mm)
| Type | ØA | ØB | ØC | W | T | Paper Type(EA) | Emboss Plastic Tape(EA) |  |
|---|---|---|---|---|---|---|---|---|
| ARN06 | 178.0±1.0 | 60.0+1.0 | 13.5±0.7 | 9.5±1.0 | 11.5±1.0 | 5,000 | - | |
| ARN12 | 178.0±1.0 | 60.0+1.0 | 13.5±0.7 | 13.5±1.0 | 15.5±1.0 | - | 4,000 |
Paper Tape Specifications
| Type | A | B | W | E | F | P0 | P1 | P2 | ΦD0 | T |
|---|---|---|---|---|---|---|---|---|---|---|
| ARN06 | 2.00±0.05 | 3.55±0.05 | 8.00±0.10 | 1.75±0.05 | 3.5±0.05 | 4.00±0.10 | 4.00±0.10 | 2.00±0.05 | 1.55±0.05 | 0.75±0.05 |
☑ Peel force of top cover tape
☑ The peel speed shall be about 300mm/min±5%
☑ The peel force of top cover tape shall be between 8gf to 60gf
Emboss Plastic Tape Specifications (Unit: mm)
| Type | A | B | W | E | F | P0 | P1 | P2 | ØD0 | T |
|---|---|---|---|---|---|---|---|---|---|---|
| ARN12 | 3.40±0.10 | 6.65±0.10 | 12.0±0.10 | 1.75±0.10 | 5.5±0.05 | 4.00±0.10 | 4.00±0.10 | 2.00±0.05 | 1.50±0.10 | 1.00±0.20 |
☑ Peel force of top cover tape
☑ The peel speed shall be about 300mm/min±5%
☑ The peel force of top cover tape shall be between 20gf to 80gf
- Dateien herunterladen
Hauptprodukt
MEDIZINISCHE ANWENDUNGEN
Keramische Hochfrequenz-Chip-Induktoren, klein bis 01005. Dünnschicht-, Mehrschicht-, Drahtgewickelte-,...
Weiterlesen
KOMMUNIKATIONSANWENDUNGEN
Mehrschicht-Keramikkondensator bietet hohe Spannung, hohe Frequenz, geringes Rauschen, hohe Güte, niedrige...
Weiterlesen